product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12584_lxb2-rs2 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 9 degrees 85 % 21.000 available ordering number family type led color diameter height style optic material holder material fastening status ca12844_lxb2-o-90 leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 10+36 degrees 80 % 4.680 available ordering number family type led color diameter height style optic material holder material fastening status ca12665_lxb2-d leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 12 degrees 80 % 11.500 available ordering number family type led color diameter height style optic material holder material fastening status ca12666_lxb2-m leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 22 degrees 81 % 4.590 available october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 ordering number family type led color diameter height style optic material holder material fastening status ca12667_lxb2-w leila assembly xb-d black 21.6 mm 14.6 mm round pmma pc tape ready fwhm efficiency cd/lm gerber file 41 degrees 81 % 1.630 available note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet leila series last update 4/6/2012 general information - product series especially designed & optimized for xb-d series of leds. - special care taken to make light distribution as uniform as possible. - lens material optical grade pmma with high uv and temperature resistance (105 degrees of celcius / 220 degrees of fahrenheit). allows use of high current and temperature conditions. please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/pmma%208n%20plexiglas-datasheet.pdf - optic holder molded by high quality pc material (120 dergees of celcius / 248 degrees of fahrenheit). - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 19th 2012 0:25 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a b c a d 3 2 3 2 4 1 4 1 designed by date checked by date drawn by date this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight(g) sheet 1/1 size a4 drawing number rev 1 drawing title ledil oy salorankatu 10 fin 24240 salo finland datasheet lxb2 tape assy - pv 11.04.2012 sn pv 19.01.2012 19.01.2012 lens holder tape materials: lens pmma holder pc, black tape pu foam with psa tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm 14.6 2.5 21.6 isometric view scale: 1:1
|
